Book My Estimate

 

They are making a number of good pointers relating to A Step-by-Step Guide to Installing a Bathtub in general in this great article beneath.

Mounting a tub isn't specifically brain surgery, but it does require solid plumbing, woodworking, and sometimes, tiling skills. Replacing an old bathtub with a new one is likewise a reasonably hard job. If the old tub is easily available, the task can relocate rapidly; if you need to open up a wall to eliminate the old bathtub and also position the brand-new tub, the task is a lot harder. In either instance, the job is within a home handyman's abilities, although you will certainly require an assistant to leave the old bathtub as well as set in the brand-new one. Make certain you have actually qualified on your own for the job and also are comfortable trying it. As opposed to hiring a professional to take control of a halfway-completed task, it is better to take into consideration employing one before you begin. Chances are you might require a professional plumber to make tube connections.
This short article will assist you set up a new bath tub in your shower room if you have actually currently acquired a brand-new bathtub as well as don't need to change the arrangement of your previous water system pipelines.
Your devices and material checklist should comprise the following:

 

• New Tub


• Hammer


• Pipeline Wrenches


• Prybar


• Safety Glasses


• Level


• Pliers


• Adjustable Wrench


• Putty Knife


• Screwdriver


• Cold Blade


• Measuring tape


• Pipeline Caps


 

Planning for the Installment

To start with, the sustaining structure supplied with the bathroom should be fitted (if called for) according to the producer's guidelines. Next off, fit the taps or mixer to the bathtub. When fitting the tap block, it is important to ensure that if the faucet includes a plastic washing machine, it is fitted between the bath and also the taps. On a plastic bath, it is likewise practical to fit a supporting plate under the faucets system to prevent stress on the bath tub.
Fit the adaptable faucet ports to the bottom of the two faucets using 2 nuts and olives (often provided with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Make use of the nut supplied by the supplier to fit the plug-hole. Examine the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit the end of the versatile overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which ought to be fitted inside the bath. Make sure you utilize every one of the supplied washing machines.
Connect the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste outlet with silicone mastic or PTFE tape, as well as screw on the catch to the outlet. Link the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its last position.

 

 

Removing Old Touches

If you need to change old faucets with brand-new ones as a part of your installation, then the first thing you need to do is separate the water system. After doing so, switch on the taps to drain pipes any type of water staying in the system. The process of removing the existing taps can be quite troublesome as a result of the restricted gain access to that is usually the situation.
Utilize a container wrench (crowsfoot spanner) or a faucet device to undo the nut that connects the supply pipes to the faucets. Have a fabric prepared for the staying water that will originate from the pipelines. Once the supply pipes have actually been eliminated, make use of the same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to stop the single taps from transforming throughout this procedure. As soon as the taps have been removed, the holes in the bath/basin will need to be cleaned of any old sealing compound.
Before going on to fit the brand-new taps, contrast the pipeline links on the old taps to the brand-new faucets. If the old taps are longer than the new taps, then a shank adapter is required for the brand-new faucets to fit.

 

 

Installing the Bath tub

Utilizing both wood boards under its feet, position the bathtub in the needed setting. The wooden boards are handy in equally spreading the weight of the tub over the area of the boards instead of focusing all the weight onto 4 small points.
The next goal is to guarantee that the bath tub is leveled all round. This can be achieved by checking the spirit level as well as readjusting the feet on the bath tub up until the level checks out level.
To set up taps, fit the bottom of the outermost flexible faucet adapter to the ideal supply pipeline by making a compression join; after that do the same for the other faucet.
Switch on the water system and check all joints and also brand-new pipework for leaks and also tighten them if essential. Fill up the bathtub as well as likewise check the overflow outlet as well as the regular outlet for leakages.
Finally, repair the bathroom paneling as explained in the maker's instruction manual. Tiling and also sealing around the bathtub ought to wait till the tub has been used at least when as this will certainly settle it into its last setting.

 

 

Fitting New Touches

If the tails of the brand-new taps are plastic, after that you will need a plastic port to stop damage to the string. One end of the port fits on the plastic tail of the faucet and also the other end offers a link to the current supply pipelines.
If you require to fit a monobloc, after that you will need reducing couplers, which attaches the 10mm pipe of the monobloc to the basic 15mm supply pipeline.
Next off, position the tap in the installing hole in the bath/basin ensuring that the washing machines are in area between the tap and also the sink. Safeguard the faucet in place with the producer given backnut. As soon as the faucet is safely in position, the supply pipes can be attached to the tails of the faucets. The taps can either be linked by using corrugated copper piping or with normal faucet connectors. The former type must be connected to the tap finishes initially, tightening just by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

 

 

Tiling Around the Bathtub

In the location where the bathroom satisfies the tile, it is necessary to secure the accompanies a silicone rubber caulking. This is essential as the installation can move sufficient to break an inflexible seal, causing the water to penetrate the wall surface in between the bath and also the tiling, causing problems with dampness as well as possible leakages to the ceiling listed below.
You can choose from a range of coloured sealants to blend in your fixtures and also fittings. They are offered in tubes as well as cartridges, and also can sealing gaps approximately a width of 3mm (1/8 inch). If you have a bigger space to fill up, you can fill it with spins of drenched paper or soft rope. Bear in mind to constantly fill up the tub with water prior to securing, to permit the activity experienced when the bathtub remains in use. The sealer can split rather early if you do not consider this movement before sealing.
Additionally, ceramic coving or quadrant floor tiles can be utilized to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and also cut to dimension, are also quickly readily available on the market. It is advisable to fit the floor tiles utilizing water-resistant or water resistant adhesive as well as cement.

 

A Step-by-Step Guide to Installing a Bathtub

 

Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.

But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.

This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.

 

Remove the Existing Bathtub

 

To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.

The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.

 

Choose the Right Bathtub

 

The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.

 

Install the Plumbing and Ledger Board

 

You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.

Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.

 

Install the Bathtub

 

When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.

Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.

If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.

 

Hook up the Plumbing

 

Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.

 

Install the Bathtub Surround

 

A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.

Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.

If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.

If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.

https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/

 

I came across that review about Installing A Bathtub while doing a search on the search engines. Make sure you take the opportunity to distribute this blog post if you enjoyed it. I take joy in reading our article about How to Install a Bathtub Yourself.

Urgent support required?